The M10 sensation: Euro 518i
The M10 sensation: Euro 518i
Hey guys, thought some might get a kick out of seeing this thing. I just got the car a few days ago. Some may recognize it. Drove an hour to look at the car over the holiday weekend and was impressed with the fairly original condition and uniqueness.
Loaded and ready for the trip home:
From what I can tell, it was sold by a Munich dealership to be exported to Central America where it probably lived in El Salvador from 1986-1992 or so before being imported to the US. This is based on my examination of the original service booklet and the shop stamps. Based on an old insurance card with a unique name, I'm guessing it remained with the original owner until about 2005 in the Atlanta metropolis. Another person owned it for a number of years in the metro area and sold the car last year.
The 518i is very basic and has quite a few differences when compared to the higher-spec and larger engined E28 models. I will try to document those differences during the course of repairs. For a 518i, mine has the unusual option of factory A/C. A 1985 ordering catalog I have from BMW the shows that green insulating glass (like a US car) was recommended in conjunction with A/C to improve the cooling performance and this car was so equipped. Other options are central locking, power mirrors, power steering (although this might have been standard), and a factory installed radio with power antenna.
Despite the cars current mechanical needs it appears to have been taken care of over the years. I have found rather new Euro headlamps & grilles, tail lamps, AFM, all ignition components, radiator & hoses, and catalytic convertor. It probably had to pass Georgia Clean Air emissions up until 2011 so it had to run well. Right now I have to look forward to a clutch job, brakes, shocks & struts, shifter bushings, LCAs, and rehabbing the driver's seat structure to make it a safe and comfortable E28. I would also like to obtain a more correct size tire for the 5.5" steel wheels. The 185/65s on there now are a bit short; a 185/75-14 would be a more appropriate substitute for the original 175R14s.
As far as my plans for the car, I would like to keep it original as much as possible. It has survived this long without molestation. Obviously I will be myself and go through the car, cleaning and detailing along the way while fixing things. While not detailed it is very clean throughout, including the undercarriage as would seem indicative of a lower mileage car.
I have not driven the car much to get a good feel for it, but my impression is that it is not as slow as one would think. The M10 runs a bit higher compression than the ones sold here and with such a lightweight body, it still beats the diesels. The owners manual shows a base 518i, ready for the road with a full tank of gas, as weighing 2560lbs. I don't know the weight of the A/C system, but I'm curious and have some corner balance scales.
Anyway, it will probably be a while until I get around to working on the car and sorting it out. Just for grins, I decided to clean up a section under the hood. Single stage tends to stain as it is more porous, but I'm happy to see it cleans up fairly easy with some elbow grease and a non-abrasive product. Here was a couple minutes of work on the front corner of the fender and hood latch support:
The rest of the original paint should come out well. Unfortunately the driver's side doors, rear quarter, and trunk lid were repainted and the color match is off. All panels including doors appear original and show no evidence of filler, so it was likely more innocuous reasons for the paint work. The color difference is a bit less noticeable in person depending on the light. Something to address eventually.
Here are some pictures of the interior from the seller's ad since I haven't taken any:
Loaded and ready for the trip home:
From what I can tell, it was sold by a Munich dealership to be exported to Central America where it probably lived in El Salvador from 1986-1992 or so before being imported to the US. This is based on my examination of the original service booklet and the shop stamps. Based on an old insurance card with a unique name, I'm guessing it remained with the original owner until about 2005 in the Atlanta metropolis. Another person owned it for a number of years in the metro area and sold the car last year.
The 518i is very basic and has quite a few differences when compared to the higher-spec and larger engined E28 models. I will try to document those differences during the course of repairs. For a 518i, mine has the unusual option of factory A/C. A 1985 ordering catalog I have from BMW the shows that green insulating glass (like a US car) was recommended in conjunction with A/C to improve the cooling performance and this car was so equipped. Other options are central locking, power mirrors, power steering (although this might have been standard), and a factory installed radio with power antenna.
Despite the cars current mechanical needs it appears to have been taken care of over the years. I have found rather new Euro headlamps & grilles, tail lamps, AFM, all ignition components, radiator & hoses, and catalytic convertor. It probably had to pass Georgia Clean Air emissions up until 2011 so it had to run well. Right now I have to look forward to a clutch job, brakes, shocks & struts, shifter bushings, LCAs, and rehabbing the driver's seat structure to make it a safe and comfortable E28. I would also like to obtain a more correct size tire for the 5.5" steel wheels. The 185/65s on there now are a bit short; a 185/75-14 would be a more appropriate substitute for the original 175R14s.
As far as my plans for the car, I would like to keep it original as much as possible. It has survived this long without molestation. Obviously I will be myself and go through the car, cleaning and detailing along the way while fixing things. While not detailed it is very clean throughout, including the undercarriage as would seem indicative of a lower mileage car.
I have not driven the car much to get a good feel for it, but my impression is that it is not as slow as one would think. The M10 runs a bit higher compression than the ones sold here and with such a lightweight body, it still beats the diesels. The owners manual shows a base 518i, ready for the road with a full tank of gas, as weighing 2560lbs. I don't know the weight of the A/C system, but I'm curious and have some corner balance scales.
Anyway, it will probably be a while until I get around to working on the car and sorting it out. Just for grins, I decided to clean up a section under the hood. Single stage tends to stain as it is more porous, but I'm happy to see it cleans up fairly easy with some elbow grease and a non-abrasive product. Here was a couple minutes of work on the front corner of the fender and hood latch support:
The rest of the original paint should come out well. Unfortunately the driver's side doors, rear quarter, and trunk lid were repainted and the color match is off. All panels including doors appear original and show no evidence of filler, so it was likely more innocuous reasons for the paint work. The color difference is a bit less noticeable in person depending on the light. Something to address eventually.
Here are some pictures of the interior from the seller's ad since I haven't taken any:
-
- Posts: 5616
- Joined: Sep 10, 2006 7:06 AM
- Location: Melbourne, Doooown Under
-
- Posts: 17638
- Joined: Feb 12, 2006 12:00 PM
- Location: Nasty Orleans------> Batten-Rooehjch------>More Souther LA
I think that would be fun, but don't know this car well enough yet.T_C_D wrote:Awesome Justin. That car needs boost!
I still grin thinking about the ride in your S1 535i, Todd. Hard to believe it was 9 years ago! My '88 535is is the perfect candidate. Would like to actually own a quick vehicle for once...
Gosh, do you guys plan these in secret? LOL. I probably won't be up for the trip this go around, 200 miles each way is still a drive.Coldswede wrote:That is great Justin, bring it to this months Bakery Run!
I couldn't take the 518i, it just isn't safe right now until repairs are made to the suspension and brakes.
-
- Posts: 776
- Joined: Nov 26, 2010 7:23 PM
- Location: Seattle Washington
Sia, I have no plans, really. Base-lining the car and making it a mechanically solid driver would be a good starting point! Probably use it here and there as a daily driver when the weather isn't super wet and rainy.B7Turbo wrote:Cool car Justin, lots of potential. What are your plans?
It is interesting that lately two other members (Adam and Graham) have end up with couple of nice condition lower powered euro e28s as well.
It does need a nutria dashboard, since it is cracked. Very difficult to find, so I might have to switch out for a black dash and door caps.
-
- Posts: 1425
- Joined: Nov 15, 2010 12:37 AM
- Location: Sacramento
-
- Posts: 1717
- Joined: Feb 12, 2006 12:00 PM
- Location: Baltimore, Maryland
-
- Posts: 82
- Joined: Dec 14, 2012 9:00 AM
- Location: South
-
- Posts: 2442
- Joined: Feb 14, 2008 7:28 PM
- Location: Toronto
-
- Posts: 6859
- Joined: Oct 10, 2008 1:48 PM
- Location: Back U.P. North,. Where the water's blue, the wind is free and seasons four.
Sorry Justin, I do not have your e-mail address to copy you the Bakery run planning questions. I just sent the email out anyway, so not much secrecy there. There will be a thread in General when we decide if/when most of us can make it.Justin_FL wrote:Gosh, do you guys plan these in secret? LOL. I probably won't be up for the trip this go around, 200 miles each way is still a drive.Coldswede wrote:That is great Justin, bring it to this months Bakery Run!
I couldn't take the 518i, it just isn't safe right now until repairs are made to the suspension and brakes.
That could be fun but not sure about motor mounts and oil pan. Many M10 items appear specific to the E28. Probably less work to turbo the engine in the car if I need more HP.symmat001 wrote:I wonder how easy an m42 swop would be, mounting points etc?
Hey Randy, I was just joking. You probably have my address but don't realize it from the emails Tim sends out. We should use a Yahoo group or something to manage an email list. I did set one up a couple years ago but that was when Randy C. was still involved in the pep rally duties so I never pushed for its use. This way you just send a single email to one address and the distribution goes out to everyone and you don't have to worry about keeping your address book up to date and people can come and go as they please. I could also run something on our server here and let other groups use it if they see fit (with their own dedicated email list, of course). Most of the free services will have ads and what not.Coldswede wrote:Sorry Justin, I do not have your e-mail address to copy you the Bakery run planning questions. I just sent the email out anyway, so not much secrecy there. There will be a thread in General when we decide if/when most of us can make it.
I believe it is a 4.10.Mark in Toronto wrote:Any idea of the final drive ratio?
-
- Posts: 1007
- Joined: Feb 12, 2006 12:00 PM
- Location: Toronto, Ontario, Canada
- Contact:
Time flies! I have a nice tubular m10 manifold that I have been saving for such a project. 15psi and MS on that car would make it really fun, allow you to install a 373LSD and possibly achieve 30mpg and 220hp. That would be very cool.Justin_FL wrote:I think that would be fun, but don't know this car well enough yet.T_C_D wrote:Awesome Justin. That car needs boost!
I still grin thinking about the ride in your S1 535i, Todd. Hard to believe it was 9 years ago! My '88 535is is the perfect candidate. Would like to actually own a quick vehicle for once...
It would be faster than a stock e28 M5.
-
- Posts: 127
- Joined: Dec 16, 2011 7:19 PM
- Location: Seminole FL
-
- Posts: 313
- Joined: Feb 12, 2006 12:00 PM
- Location: Surrey
Does your 518i have the rear drum brakes?Justin_FL wrote: I couldn't take the 518i, it just isn't safe right now until repairs are made to the suspension and brakes.
How about a rear sway bar? Mine does not even have mounting points for the sway bar on the trailing arms.
Does it have the 4.27 differential in it? How about the CV joint connecting the driveshaft to the differential?